SECTION 08388
DOUBLE ACTING IMPACT TRAFFIC DOOR
[TL
250®]
|
GENERAL
NOTES TO SPECIFIER: |
|
THIS
SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE
PREPARATION OF PROJECT OR OFFICE MASTER SPECIFICATIONS. IT FOLLOWS GUIDELINES
ESTABLISHED BY THE CONSTRUCTION SPECIFICATIONS INSTITUTE, AND THEREFORE MAY
BE USED WITH MOST MASTER SPECIFICATION SYSTEMS WITH MINOR EDITING. |
|
EDIT CAREFULLY TO SUIT PROJECT REQUIREMENTS.
MODIFY AS NECESSARY AND DELETE ITEMS THAT ARE NOT APPLICABLE. VERIFY THAT
REFERENCED SECTION NUMBERS AND TITLES ARE CORRECT. (NUMBERS AND TITLES
REFERENCED ARE BASED ON MASTERFORMAT,
1995 EDITION). |
|
THIS SECTION ASSUMES THE
PROJECT MANUAL WILL CONTAIN COMPLETE DIVISION 1 DOCUMENTS INCLUDING SECTIONS
01330–SUBMITTAL PROCEDURES, 01620–PRODUCT OPTIONS, 01630–PRODUCT SUBSTITUTION
PROCEDURES, 01660–PRODUCT STORAGE AND HANDLING REQUIREMENTS, 01770–CLOSEOUT
PROCEDURES, AND 01780–CLOSEOUT SUBMITTALS. CLOSE COORDINATION WITH DIVISION 1
SECTIONS IS REQUIRED. IF THE PROJECT MANUAL DOES NOT CONTAIN THESE SECTIONS,
ADDITIONAL INFORMATION SHOULD BE INCLUDED UNDER THE APPROPRIATE ARTICLES. |
|
THIS IS AN OPEN PROPRIETARY
SPECIFICATION ALLOWING USERS THE OPTION OF APPROVING OTHER MANUFACTURERS
WHICH COMPLY WITH THE CRITERIA SPECIFIED HEREIN. |
|
NOTES TO THE SPECIFIER ARE
CONTAINED IN BOXES AND SHOULD BE DELETED FROM FINAL COPY. |
|
OPTIONAL ITEMS REQUIRING
SELECTION BY THE SPECIFIER ARE ENCLOSED WITHIN BRACKETS, E.G.: [35] [40]
[45]. MAKE APPROPRIATE SELECTIONS AND DELETE OTHERS. |
|
ITEMS REQUIRING ADDITIONAL
INFORMATION ARE UNDERLINED BLANK SPACES, E.G.: _____________ . |
|
OPTIONAL PARAGRAPHS ARE
SEPARATED BY “OR” WITHIN A BOX, E.G.: OR |
|
|
PART
1 GENERAL
65535.1 SUMMARY
A. Section Includes: Double acting, self
closing, 1/4 inch (6 mm) thick ABS impact traffic door [with extruded aluminum
frame].
|
INCLUDE APPROPRIATE
SECTION(S) BELOW FOR OPENING FRAMING AND DOOR FRAMES. RECOMMENDED FRAME IS A
6 INCH (152 mm) STEEL CHANNEL WITH A 3/8 INCH (10 mm) WEB (MC6 X 18.0).
RUBBAIR EXTRUDED ALUMINUM FRAMES CAN BE SPECIFIED IF DESIRED AND ARE INCLUDED
IN THIS SECTION AS AN OPTION. |
B. Related Sections:
|
INCLUDE APPROPRIATE
LANGUAGE BELOW INCLUDING A REFERENCE TO SECTION 01030–ALTERNATES, IF PRODUCTS
SPECIFIED IN THIS SECTION ARE SUBJECT TO ANY ALTERNATE BID ITEMS, AND ADD
SECTION 01030 TO 1.1 B. OTHERWISE DELETE FOLLOWING PARAGRAPH |
C. Alternates:
65535.2 SUBMITTALS
A. Reference Section 01330–Submittal
Procedures; submit the following items:
1. Product Data.
2. Shop Drawings: Show fabrication details and
anchorage. Include door elevations, head, jamb and meeting stile details.
3. Samples: Full range of manufacturer’s
standard color selections for facing material.
4. Quality Assurance/Control Submittals:
a. Manufacturer’s Installation Instructions.
5. Closeout Submittals:
a. Cleaning and Maintenance instructions.
b. Warranty
65535.3 QUALITY ASSURANCE
A. Qualifications:
1. Manufacturer Qualifications: Minimum five years
experience in producing doors of the
type specified.
65535.4 DELIVERY STORAGE AND HANDLING
A. Reference Section 01660–Product Storage and
Handling Requirements.
B. Verify doors were shipped in upright
position.
1. Note specific doors shipped in other than
upright position on bill of lading and contact manufacturer.
C. Store in upright position and follow
manufacturer’s instructions printed on carton.
65535.5 PROJECT/SITE CONDITIONS
A. Existing Conditions: Frames installed under
other sections shall be level and plumb.
65535.6 WARRANTY
A. One year against defects in materials and
workmanship.
PART
2 PRODUCTS
2.1 MANUFACTURERS
A. Manufacturer: RubbAir Door–Division of Eckel
Industries, Inc.;100 Groton Shirley Rd.; Ayer, MA 01432-1050. Telephone: (800)
966-7822, (978) 772-0480. Fax: (978) 772-7114.
|
INSERT NAME, ADDRESS AND PHONE
NUMBERS OF LOCAL DISTRIBUTOR BELOW. |
1. Distributor:
B. Model: TL 250®.
C. Substitutions: Reference Section 01630–Product
Substitution Procedures.
2.2 DOOR
COMPONENTS.
A. Panel: 1/4 inch (6 mm) thick ABS plastic,
5,400 psi (37 MPa) tensile strength,
color as selected by architect.
B. Back Strip: 1/4 inch (6 mm) thick ABS
plastic, 6 inches (150 mm) wide, both sides of panel, full height with satin
anodized aluminum channel cap.
C. Offset Pivot Hardware:
1. Top Assembly:
a. 11 gauge zinc plated steel enclosure with
screw adjustable “V” plate bearing guide.
b. 11 gauge zinc plated steel door mounting
bracket with case hardened steel clevis pin and two 7/8 inch (22 mm) diameter
steel bearings.
c. 11 gauge zinc plated steel head/jamb
mounting angle.
2. Bottom Assembly:
a. 11 gauge zinc plated door mounting bracket
with 3/4 inch (19 mm) diameter solid steel plug.
b. Floor/jamb mounted zinc plated steel jamb
guard with integral, low friction, igus bearing.
|
8X10 INCH (200x250
mm) VISION PANEL IS STANDARD; OPTIONS INCLUDE 11-1/2 X 15-1/2 (290X380 mm),
14X16 (350X400 mm) and 16X18 (405X455 mm). SHOW PANEL SIZE AND LOCATION ON
DRAWINGS. |
D. Vision Panel: Flush 3/16 inch (5 mm) thick
polycarbonate, single glazed in rubber gasket with radiused corners.]
2.3 [DOOR
FRAMES
A. 2x4 inch (50x100 mm) extruded aluminum “L”
shaped sections, 3/16 inch (5 mm) minimum thickness. Corners mitered,
reinforced and welded.
B. Provide number, type and size of fasteners
to solidly anchor frame in rough opening.]
|
FOLLOWING ACCESSORIES ARE
OPTIONAL. SELECT AS DESIRED AND DELETE OTHERS. |
2.4 ACCESSORIES
A. Impact Panels: [12 inch (300 mm)] [24 inch
(600 mm)] [36 inch (900 mm)] [48 inch (1.22 m)] high, 1/8 inch (3 mm) thick
vinyl or ABS, color as selected by Architect.
B. Wear Strips: 1/4 inch (6 mm) thick high
density polyethelene, ____ inches (___
mm) high by full width of panel; black.
|
FOLLOWING LOCKING DEVICE IS
STANDARD FOR PADLOCK (NOT SUPPLIED); CONTACT RUBBAIR FOR OTHER OPTIONS. |
C. Locking Device: 1 inch (25 mm) i.d. cast
aluminum bushing (2 per leaf) with two 3/16 inch (5 mm) by 30 inch (760 mm)
long galvanized proof coil chains.
D. Transom Flap: 2 ply vinyl, color as selected
by Architect.
|
TRACK PORTS AND MEAT RAIL
CUTOUTS, IF REQUIRED, SHOULD BE SHOWN ON DRAWINGS. |
2.5 FABRICATION
A. Shop Assembly: Fabricate door and back strip
into adhesive bonded, unitized assembly. Secure top and bottom offset pivot
hardware to door with through bolts.
2.6 SOURCE
QUALITY CONTROL
A. Fabrication Tolerances: Width and height of
each leaf: + 0, -1/8 inch (3 mm) .
PART
3 EXECUTION
3.1 EXAMINATION
A. Examine opening in which door will be
installed.
B. Coordinate with responsible entity to
perform corrective work on unsatisfactory conditions.
C. Commencement of work by installer is
acceptance of opening conditions.
3.2 INSTALLATION
A. Follow manufacturer’s instructions.
B. [Install frames plumb and level.]
C. Install door with necessary anchors,
hardware and accessories.
3.3 ADJUSTING
A. Follow manufacturer’s instructions as
required to:
1. Clean and lubricate operating parts.
2. Adjust to open and close smoothly and
freely without binding.
3. Check seals for proper fit.
3.4 CLEANING
A. Clean surfaces soiled by work as recommended
by manufacturer.
B. Remove surplus materials and debris from the
site.
END OF SECTION[1]